电磁阀的故障及排除方法

由此快速通道进入阀门产品分类导航，了解 : 上海赛泰泵阀有限公司强大的团队一定能满足您对各类特殊泵阀产品的需求，供您选择最适合您的产品，我们的水泵、阀门技术工程师团队随时恭候您的垂询！由此快速通道进入阀门产品分类导航，了解 :球阀闸阀截止阀蝶阀止回阀柱塞阀等系列阀门的产品、型号、技术与支持。

原文：
电磁阀的故障及排除方法：电磁阀的故障将直接影响到切换阀和调节阀的动作，常见的故障有电磁阀不动作，应从以下几方面排查：　　1、电磁阀接线头松动或线头脱落，电磁阀不得电，可紧固线头。　　2、电磁阀线圈烧坏，可拆下电磁阀的接线，用万用表测量，如果开路，则电磁阀线圈烧坏。原因有线圈受潮，引起绝缘不好而漏磁，造成线圈内电流过大而烧毁，因此要防止雨水进入电磁阀。此外，弹簧过硬，反作用力过大，线圈匝数太少，吸力不够也可使得线圈烧毁。紧急处理时，可将线圈上的手动按钮由正常工作时的“0”位打到“1”位，使得阀打开。　　3、电磁阀卡住。电磁阀的滑阀套与阀芯的配合间隙很小(小于0.008mm)，一般都是单件装配，当有机械杂质带入或润滑油太少时，很容易卡住。处理方法可用钢丝从头部小孔捅入，使其弹回。根本的解决方法是要将电磁阀拆下，取出阀芯及阀芯套，用CCI4清洗，使得阀芯在阀套内动作灵活。拆卸时应注意各部件的装配顺序及外部接线位置，以便重新装配及接线正确，还要检查油雾器喷油孔是否堵塞，润滑油是否足够。　　4、漏气。漏气会造成空气压力不足，使得强制阀的启闭困难，原因是密封垫片损坏或滑阀磨损而造成几个空腔窜气。　　在处理切换系统的电磁阀故障时，应选择适当的时机，等该电磁阀处于失电时进行处理，若在一个切换间隙内处理不完，可将切换系统暂停，从容处理。

“Solenoid valve failure and troubleshooting”,是由中国电磁阀网提供的国际阀门新闻，译文仅供参考。另外，中国电磁阀网还提供相关产品搜索：出口电磁阀、防爆电磁阀、蒸汽电磁阀、液体电磁阀、气体电磁阀、等。

译文：
Solenoid valve failure and troubleshooting Solenoid valve failure and troubleshooting: solenoid valve failure will directly affect the switching valve and valve action, a common fault with the solenoid valve does not move, the investigation from the following aspects: 1, the first solenoid valve wiring or loose thread off, electric solenoid valve shall be fastened thread. 2, the solenoid valve coil burned out, remove the solenoid valve wiring, measured with a multimeter, if open, the solenoid valve coil burnt. Moisture causes the coil, magnetic flux leakage caused by bad insulation, causing the coil current is too large to burn, so to prevent flood water from entering the solenoid valve. In addition, excellent spring, the reaction is too large, too few turns, enough suction makes the coil can also be burned. Emergency treatment, can be manual button on the coil from the normal work of the "0" bit hit "1" bit to allow the valve to open. 3, the solenoid valve stuck. Solenoid valve slide valve sleeve and spool with the gap is very small (less than 0.008mm), usually one-piece assembly, when there is too little mechanical impurities into or lubricant, it is easy to get stuck. Approach can hold into the wire hole from the head to make it bounce. Fundamental solution is to remove the solenoid valve, remove the spool and spool cover, with CCI4 cleaning, making the spool valve comprising a flexible movement. Demolition should pay attention to all parts of the assembly sequence and location of the external wiring for re-assembly and wiring is correct, also check the oil mist injector holes are blocked, oil is adequate. 4, leakage. Lack of air pressure can cause leakage, making difficult to force the valve open and close due to the slide valve gasket damage or wear caused by several cavity channeling gas. In dealing with the solenoid valve switching system failure, should select the appropriate time, such as the solenoid valve is energized when dealing with, if dealt with in an endless space switch can switch the system to pause, calm handling.

更多新闻：

原文来源：http://www.diancifa.com/

2011-12-29 07:15